| DTP T DWP 4K 332 D |
|
 specification |
|---|
 |
| Frame rate1 | 24, 25, 30, 502, or 602 fps
|
| Chroma sampling1 | 4:4:4, 4:2:2, or 4:2:02 |
| Color bit depth1 | 8 bits per color |
| Signal type1 | HDMI 1.4 , DisplayPort 1.1a, HDCP 1.4 |
| Max. video data rate1 | |
| HDMI | 10.2 Gbps (3.4 Gbps per color) |
| DisplayPort | 10.8 Gbps (2.7 Gbps per lane) |
| NOTE | 1Subject to the maximum data rate limit. Use our calculator (www.extron.com/8Kdatarate) to determine video parameters supported by this data rate.
2Applicable to HDMI signals only. |
|
| | |
|
| Video |
|---|
| HDMI input | |
| Maximum data rate | 10.2 Gbps (3.4 Gbps per color) |
| Maximum pixel clock | 300 MHz |
| Resolution range | Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz,
UHD (3840x2160) @ 30 Hz, 4K/UHD @ 60 Hz with 4:2:0 chroma subsampling
(*Reduced blanking) |
| Formats | RGB and YCbCr digital video |
| Standards | DVI 1.0, HDMI 1.4 |
| DisplayPort Input | |
| Maximum data rate | 10.8 Gbps (2.7 Gbps per lane) |
| Maximum pixel clock | 300 MHz |
| Resolution range | Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz
(*Reduced blanking) |
| Formats | RGB and YCbCr digital video |
| Standards | DisplayPort 1.1a |
|
| Video input |
|---|
| NOTE | *Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input/output. |
|
| Number/signal type | |
| HDMI input | 1 single link HDMI (or single link DVI-D*) input |
| DisplayPort Input | 1 DisplayPort |
| Connectors | |
| HDMI input | 1 female HDMI, type A |
| DisplayPort Input | 1 female DisplayPort |
|
| Interconnection between transmitter and receiver |
|---|
| Signal Type | 1 DTP 330 output |
| Connectors | 1 female RJ-45 jack |
| Termination standards | TIA/EIA T568B |
| DTP signal | |
| Signal transmission distance | |
| 1080p @ 60 Hz | Up to 330' (100 m) using shielded twisted pair (STP) cable or XTP DTP 24 cable |
| 2560x1600 @ 60 Hz | Up to 330' (100 m) using STP cable or XTP DTP 24 cable |
| 4K/UHD @ 30 and 60 Hz | Up to 330' (100 m) using STP cable or XTP DTP 24 cable |
| Cable requirements | Solid conductor, 24 AWG or better |
| Cable recommendations | 400 MHz bandwidth STP cable |
| NOTE | Extron XTP DTP 24 shielded twisted pair cable is strongly recommended for optimal performance. |
|
| NOTE | Output mode signaling:
DTP: HDMI with embedded audio, analog audio, RS-232 and IR, and remote power
HDBaseT: HDMI with embedded audio plus RS-232 and IR |
|
|
| Audio |
|---|
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.03% @ 1 kHz at nominal level |
| S/N | >90 dB at maximum input (unweighted) |
| Stereo channel separation | >80 dB @ 1 kHz |
|
| Audio input |
|---|
| Number/signal type | 2 stereo, unbalanced |
| Connectors | (2) 3.5 mm stereo jack, 2 channel; tip (L); ring (R); sleeve (Gnd) |
| Impedance | >10k ohms, DC coupled |
| Nominal level | -10 dBV (316 mVrms) |
| Maximum level | +6 dBu, unbalanced |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Communications — switcher |
|---|
| Serial control port | RS-232 via 1 rear panel 3.5 mm, 3-pole captive screw connector |
| Pin configuration | 1 = Tx, 2 = Rx, 3 = Gnd |
| Baud rate and protocol | 9600 baud rate, 8 data bits, 1 stop bit, no parity |
| USB control port | 1 front panel female mini USB B |
| USB standards | USB 2.0, high speed |
| Program control | Extron Simple Instruction Set (SIS™) |
|
| Communications — external device (RS-232/IR over TP) |
|---|
| NOTE | Protocol is mirrored between the connected DTP 230 Rx or DTP 330 Rx endpoints and the "Over TP" ports on the
DTP T DWP 4K series. Signals from a control device pass into each "Over TP" port, are embedded with the DTP signal, and sent to the individual DTP 230 Rx or DTP 330 Rx endpoints for control of remote sink or source devices. The "Over TP" ports are simply pass-through connections to DTP endpoints. There is no RS-232 or IR insertion from any
DTP T DWP 4K control port to the "Over TP" ports. |
|
| Serial control pass-through port | Bidirectional RS-232 |
| Connector | (1) 3.5 mm captive screw connector, 5-pole (shared with IR port) |
| Baud rate and protocol | 300 to 115200 baud, 8 or 7 data bits, 1 or 2 stop bits, non-parity (default), even or odd parity |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = Gnd |
| IR pass-through control port | 1 bidirectional TTL level (0 to 5V) modulated infrared control from 30 kHz up to 60 kHz
(shared with RS-232 port) |
| IR control pin configuration | 3 = Gnd, 4 = IR Tx, 5 = IR Rx |
|
| General |
|---|
| Power supply | External
Input: 100-240 VAC, 50-60 Hz
Output: 12 VDC, 1.5 A, 18 watts |
| Power consumption | |
| Device | 6.6 watts |
| Device and power supply | 7.9 watts |
| Remote power budget | 12 watts |
| NOTE | Each transmitter or receiver can be powered either locally by an external power supply or remotely by receiver or transmitter on the other end of the twisted pair cable. |
|
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, no vents |
| Thermal dissipation | |
| Device | 22.4 BTU/hr |
| Device and power supply | 27.0 BTU/hr |
| Enclosure type | Metal |
| Enclosure dimensions | |
| Faceplate | Two 2.6" H* x 1.3" W x 0.2" D
(6.6 cm H x 3.3 cm W x 0.6 cm D)
Fits the opening in a 2 gang decorator wallplate |
| Device | Two 2.7" H x 3.5" W x 1.9" D
(6.9 cm H x 8.9 cm W x 4.8 cm D) |
| Product weight | 0.4 lbs (0.2 kg) |
| Regulatory compliance | CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES, VCCI,
Complies with the appropriate requirements of RoHS, WEEE |
| NOTE | **CE and FCC testing is conducted with STP cable. |
|
| Product warranty | 3 years parts and labor |
| Everlast power supply warranty | 7 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (5345-D9) |