| FOX 500 Rx |
| NOTE | The FOX 500 Rx is a receiver with one or two fiber optic cables linking it to a transmitter. |
|
| NOTE | The analog RGB input signal is digitized pixel for pixel in the transmitter, sent digitally through the fiber cable, and converted back to analog RGB in the receiver. |
|
| NOTE | The analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver. |
|
| NOTE | This receiver is a class 1 laser product. It meets the safety regulations of IEC-60825. |
|
|
| Optical fiber interconnection between transmitter and receiver |
|---|
| Number/type | 1 or 2 fiber optic |
| NOTE | Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit return data for bidirectional control and communication. |
|
| Connectors | 2 LC connectors |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with an SM unit |
| Multimode | 300 m (985') with 62.5 µm OM1 multimode (MM) cables with an MM unit
1 km (3280') with 50 µm OM2 multimode (MM) cables with an MM unit
2 km (6561') with 50 µm OM3/OM4 laser optimized multimode cable with an MM unit |
| NOTE | Operating distance is approximate. These are typical maximum distances that may vary depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for MM units, 1310 nm for SM units |
| Data rate | 4.25 Gbps |
| Transmission power | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
|
| Video |
|---|
| Number/signal type | VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs, or HD component
|
| Gain | Unity |
| Pixel data bit depth | 8 bits per channel, 3 channels (R, G, B) |
| Maximum resolution | 1600x1200 or 1080p @ 60 Hz, digitized pixel for pixel; higher resolutions up to 2048x1120, undersampled |
|
| Video output |
|---|
| Number/signal type | 2 VGA-UXGA RGBHV, RGBS, RGsB, RsGsBs (follows input or can be set by user) |
| Connectors | 1 x 6 female BNC and (1) female 15-pin HD |
| Nominal level | 0.7 Vp-p for RGB |
| Minimum/maximum levels | 0.3 V to 1.5 Vp-p |
| Impedance | 75 ohms |
| Return loss | -40 dB @ 5 MHz |
| DC offset | ±5 mV with input at 0 offset |
| Video delay | 1-2 frames |
|
| Sync |
|---|
| Output type | RGBHV, RGBS, RGsB, RsGsBs (follows input or can be set by user), or component video |
| Output level | TTL: 5.0 Vp-p, unterminated, on HV, for RGBHV, RGBS
0.3 Vp-p for component video (bi-level sync, unterminated) or for Gs (SOG), terminated
0.6 Vp-p for component video (tri-level sync) |
| Output impedance | 75 ohms |
| Polarity | Positive or negative (follows input or can be set by user) |
|
| Audio |
|---|
| Gain | |
| Range | Adjustable, -18 dB to +10 dB |
| Default | |
| Captive screw connector | Unbalanced output: -6 dB; balanced output: 0 dB |
| Mini stereo jack | Unbalanced output: 0 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.10% @ 1 kHz at nominal level |
| S/N | >80 dB at maximum output (unweighted) |
| CMRR | 65 dB @ 20 Hz to 20 kHz |
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) |
| Sampling rate | 48 kHz |
|
| Audio output |
|---|
| Number/signal type | 2 buffered outputs: 1 balanced stereo; 1 unbalanced stereo or 2 unbalanced mono |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole
(1) 3.5 mm mini stereo jack |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Nominal level | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level (Hi-Z) | >+19 dBu, unbalanced at 1% THD+N |
| Maximum level (600 ohm) | >+15 dBm, unbalanced at 1% THD+N |
| Audio delay | 1.5 frames |
|
| Control/remote |
|---|
| Serial control ports |
| Control | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel)
1 RS-232, 2.5 mm mini stereo jack (front panel) |
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (3 pins are used) (rear panel) |
| Baud rate and protocol | |
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through | 9600 to 115,200 baud |
| Serial control pin configurations | Captive screw connectors: 1 = Tx, 2 = Rx, 3 = GND
Mini stereo jack: tip = Tx, ring = Rx, sleeve = GND |
| | |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power supply | Internal
Input: 100-240 VAC, 50-60 Hz |
| Power consumption | 10.9 watts |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on top and sides |
| Mounting | |
| Rack mount | Yes, with optional rack shelf kit |
| Furniture mount | Yes, with optional under desk mounting kit |
| Enclosure type | Metal |
| Enclosure dimensions | 1.7" H x 8.7" W x 9.5" D (1U high, half rack wide)
(4.3 cm H x 22.1 cm W x 24.1 cm D)
(Depth excludes connectors and knobs.) |
| Product weight | 2.3 lbs (1.0 kg) per unit, 4.6 lbs (2.1 kg) per pair |
| Shipping weight | 4 lbs (2 kg) per unit, 8 lbs (4 kg) per pair |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.1-112514-D2) |