| PowerCage™ FOX Rx HDMI |
| NOTE | The PowerCage FOX Rx HDMI board is not compatible with the FOX 3G HD-SDI, FOX 3G DVC, or FOX AV models. |
|
| NOTE | The PowerCage FOX Rx HDMI board is available in singlemode or multimode version. |
|
| NOTE | The PowerCage FOX Rx HDMI board is a class 1 laser products. It meets the safety regulations of IEC-60825. |
|
|
| Optical fiber interconnection between transmitter and receiver |
|---|
| Number/type | 1 singlemode or 1 multimode fiber optic input and output per FOX board |
| NOTE | Only one fiber is required to transmit video, audio, and unidirectional data. A second fiber is required to transmit HDMI video with HDCP content or return data for bidirectional control and communication. |
|
| Connectors | 2 bidirectional LC connectors per FOX board |
| Operating distance | |
| Singlemode | 30 km (18.75 miles) with singlemode (SM) cables with a SM board |
| Multimode | 300 m (985') with 62.5 µm OM1 multimode (MM) cable and a MM board
1 km (3280') with 50 µm OM2 multimode (MM) cable and a MM board
2 km (6561') with 50 µm OM3/OM4 2000 MHz bandwidth laser optimized MM cable and a MM board |
| NOTE | Operating distance is approximate. These are typical distances. The maximum distance may be greater than these typical numbers depending on factors such as fiber type, fiber bandwidth, connector splicing, losses, modal or chromatic dispersion, environmental factors, and kinks. |
|
| Nominal peak wavelength | 850 nm for multimode (MM), 1310 nm for singlemode (SM) |
| Transmission power, singlemode or multimode | -5 dBm, typical |
| Maximum receiver sensitivity | |
| Singlemode | -18 dBm, typical |
| Multimode | -12 dBm, typical |
| Optical loss budget | |
| Singlemode | 13 dB, maximum |
| Multimode | 7 dB, maximum |
| Maximum channel data rate | 4.25 Gbps |
|
| Video |
|---|
| NOTE | Appropriate HDMI to DVI-D cables or adapters are required for DVI signal input and output. |
|
| Maximum data rate | 4.25 Gbps |
| Maximum pixel clock | 165 MHz |
| Resolution range | 640x480 up to 1920x1200 @ 60Hz, including 480p, 576p, 720p, 1080i,
1080p @ 60Hz, sampled pixel for pixel; higher resolution 2K (2048x1080) @ 60 Hz, undersampled |
| Formats | RGB and YCbCr digital video |
| Standards | DVI 1.0, HDMI, HDCP 1.1, CEA-861E |
|
| Video output |
|---|
| Number/signal type | 1 single link HDMI |
| Connectors | 1 female 19-pin HDMI type A |
|
| Audio |
|---|
| NOTE | On PowerCage FOX boards, the analog audio signals are digitized in the transmitter, sent through the fiber cable, and converted back to analog audio in the receiver. |
|
| Gain | |
| Range | Adjustable, -18 dB to +10 dB |
| Default | Unbalanced output: -6 dB; balanced output: 0 dB |
| Frequency response | 20 Hz to 20 kHz, ±0.5 dB |
| THD + Noise | 0.10% @ 1 kHz at nominal level |
| S/N | >80 dB at maximum output (unweighted) |
| CMRR | 65 dB @ 20 Hz to 20 kHz |
| Audio bits per sample | 18 bits per channel, 2 channels (L, R) |
| Sampling rate | 48 kHz |
|
| Audio output |
|---|
| Number/signal type | 1 stereo, balanced/unbalanced or
2 mono, balanced/unbalanced |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | 50 ohms unbalanced, 100 ohms balanced |
| Nominal level | +4 dBu (1.23 Vrms), -10 dBV (316 mVrms) |
| Maximum level (Hi-Z) | >+11.0 dBu, balanced at 1% THD+N |
| Maximum level (600 ohm) | >+10.0 dBu, balanced at 1% THD+N |
| Audio delay | 1.5 frames |
|
| Control/remote |
|---|
| Serial control ports | |
| Control | 1 bidirectional RS-232, 3.5 mm captive screw connector, 5 pole (uses 3 poles; shared with the alarm port) |
| Pass-through | 1 RS-232, 3.5 mm captive screw connector, 5 pole (uses 3 poles, "RS-232 Over Fiber") |
| Baud rate and protocol | |
| Control | 9600 baud, 8 data bits, 1 stop bit, no parity |
| Pass-through | 9600 to 115,200 baud |
| Serial control pin configuration | 1 = Tx, 2 = Rx, 3 = GND |
| Program control | Extron control/configuration program for Windows®
Extron Simple Instruction Set (SIS™) |
|
| General |
|---|
| Power | Supplied by a PowerCage 1600 enclosure |
| Power consumption | 6.02 watts |
| Power input requirements | 12 VDC, 1.0 A, supplied by the PowerCage enclosure |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) / 10% to 90%, noncondensing |
| Cooling | Enclosure: fans, front to back
Boards: convection, within the PowerCage enclosure |
| Thermal dissipation | 27.6 BTU/hr |
| Dimensions | Each board fits a double slot opening in a PowerCage enclosure. |
| Product weight | 1.1 lbs (0.5 kg) |
| Shipping weight | 2 lbs (1 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Regulatory compliance | |
| Safety | CE, c-UL, UL |
| EMI/EMC | CE, C-tick, FCC Class A, ICES, VCCI |
| Environmental | Complies with the appropriate requirements of RoHS, WEEE. |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (8.1-121114-D5) |