| TLC Pro 726M Series |
|
| Display |
|---|
| Screen type | TFT Active matrix color LCD |
| Size | 7" (17.8 cm), measured diagonally |
| Resolution | 1024x600 (WSVGA) |
| Pixel density | 170 PPI |
| Aspect ratio | 17:10 |
| Color depth | 24 bit, 16.7 million colors |
| Transparency | 8 bit |
| Brightness | 420 nits (cd/m2) |
| Contrast | 700:1 |
| Backlight | LED |
| Viewing angle | ±75° horizontal, +70°/-75° vertical |
| Touch screen | Capacitive |
|
| Memory |
|---|
| RAM | 2 GB |
| Storage | 8 GB |
|
| Ethernet |
|---|
| Connectors | 1 female RJ-45 connector |
| Data rate | 10/100/1000Base-T, half/full duplex with autodetect |
| Protocols | DHCP, DNS, HTTP, HTTPS, ICMP, IEEE 802.1x, SFTP, SSH, TCP/IP, UDP/IP |
| Default settings | Link speed and duplex level = autodetected
IP address = 192.168.254.251
Subnet mask = 255.255.255.0
Default gateway = 0.0.0.0
DHCP = off
DNS = 127.0.0.1 |
|
| Software |
|---|
| Configuration software | Global Configurator Plus and Professional, GUI Designer |
| Control apps | Extron Control, iGVE |
| Resource management software | GlobalViewer Enterprise, iGVE |
| Utilities | Toolbelt, Embedded web page |
|
| Sensors |
|---|
| Motion sensor | On/off |
| Light sensor | Auto/manual |
|
| USB |
|---|
| Quantity/type | 1 high-speed USB 2.0 |
| Connectors | 1 Micro-B receptacle |
| Standards | USB 2.0, USB 1.1, USB 1.0 compatible |
| Max. data rates | Low speed (1.5 Mbps), full speed (12 Mbps), high speed (480 Mbps) |
|
| Digital input |
|---|
| Quantity/type | 1 digital input (configurable) on touchpanel |
| Connectors | (1) 3.5 mm direct insertion captive screw connector, 2 pole |
| Digital inputs | |
| Input voltage range | 0 to 24 VDC, clamped at +30 VDC |
| Input impedance | ≥10k ohms |
| Programmable pullup | 1k ohms to +5 VDC |
| Threshold low to high | 2.8 VDC |
| Threshold high to low | 2.0 VDC |
|
| Contact closure |
|---|
| Quantity/type | 1 contact closure input on USB adapter |
| Connector | (1) 3.5 mm direct insertion captive screw connector, 3-pole, shared with IR port |
| Pin configuration | Internal pullup resistor is enabled to +5 VDC, non-selectable.
The port is active when the contact pin latches to ground. |
|
| Serial |
|---|
| Quantity/type | 2 bidirectional RS-232 |
| Connector | (2) 3.5 mm direct insertion captive screw connector, 5 pole |
| Baud rate and protocol | 300 to 115200 baud (9600 baud = default); 8 (default) or 7 data bits; 1 (default) or 2 stop bits;
no parity (default), even, or odd parity |
| NOTE | This port supports software flow control. The default is no flow control. |
|
|
| Relay |
|---|
| Quantity/type | 2 normally open relays |
| Relay control connectors | (1) 3.5 mm direct insertion captive screw connector, 3 pole |
| Relay control contact rating | 24 VDC, 1 A |
|
| IR |
|---|
| Quantity/type | TTL level (0 to 5 V) infrared (carrier or non-carrier) up to 300 kHz |
| Connector | (1) 3.5 mm direct insertion captive screw connector, 3 pole, shared with Digital input |
| IR output carrier frequency | 30 kHz to 300 kHz |
|
| Audio output |
|---|
| Speaker output | 1 mono, 89 dB Max. SPL @ 0.1 m |
| Frequency response | 750 Hz to 20 kHz, ±5 dB |
| Playback format(s) | |
| Container format | WAV (Microsoft RIFF) |
| Encoding | LPCM (uncompressed) |
| Bit Depth | Unsigned 8-bit
Signed 16-bit
Signed 24-bit
Signed 32-bit |
| Sampling rate | Up to 192 kHz |
| Audio channels | Mono or stereo |
|
| General |
|---|
| Power supply | Not included |
| Power input requirements | Power over Ethernet (PoE 802.3af, class 3) |
| Power consumption — Power injector (XTP PI 100) |
| Device | 8.5 watts |
| Device and power injector | 11.6 watts |
| Auxiliary power output | |
| USB | 5 VDC, 275 mA |
| Ambient temperature/humidity | Storage: -4 to +140 °F (-20 to +60 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing |
| Cooling | Convection, vents on back |
| Thermal dissipation — Power injector (XTP PI 100) |
| Device | 24.3 BTU/hr |
| Device and power injector | 34.7 BTU/hr |
| Mounting | Wall, furniture, glass, or rack |
| Enclosure type | Plastic |
| |  |
| Enclosure dimensions | 5.05" H x 7.24" W x 1.20" D
(128 mm H x 184 mm W x 30 mm D)
Touchpanel projects 1.01" (26 mm) from the mounting surface |
| Adapter dimensions | 0.47" H x 1.81" W x 0.91" D
(12 mm H x 46 mm W x 23 mm D)
The touchpanel and adapter project 1.37" (35 mm) behind the mounting surface. |
| Enclosure + Adapter dimensions | 5.05" H x 7.24" W x 1.96" D
(128 mm H x 184 mm W x 50 mm D) |
| Product weight | 1.15 lbs (0.52 kg) |
| Regulatory compliance | BIS, CE, C-Tick, c-UL,FCC Class A, ICES, RoHS, UL, VCCI, WEEE |
| Product warranty | 3 years parts and labor; touchpanel display and overlay components are covered for 1 year |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (5281-D4) |