| TPS150: TPT150 and TPR150 |
|
| Video |
|---|
| Gain | Unity |
| Crosstalk | -42 dB @ 10 MHz |
| Number/signal type | 1 set of proprietary analog signals |
| Connectors | 1 RJ-45 female jack |
|
| Video input |
|---|
| Number/signal type | |
| TPT150 | 1 VGA-UXGA RGBHV with 1 RGB buffered local monitor loop-through
1 VGA-UXGA RGBHV
2 component video (Y, R-Y, B-Y), or S-video, or composite video |
| TPR150 | 1 set of proprietary analog signals from a TPT150 |
| Connectors | |
| TPT150 | 2 female 15-pin HD (RGB input)
1 female 15-pin HD (RGB loop-through)
2 sets of [3 female RCA (component video), 1 female RCA (composite), 1 female 4-pin mini DIN (S-video)] |
| TPR150 | 1 female RJ-45 jack |
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for R-Y and B-Y of component video, and for C of S-video |
| Minimum/maximum levels | Analog: 0.3 V to 1.5 Vp-p with no offset at unity gain |
| Impedance | 75 ohms |
| Return loss | <-40 dB @ 5 MHz |
| DC offset (max. allowable) | ±50 mV |
|
| Video output |
|---|
| Number/signal type | |
| TPT150 | 1 set of proprietary analog signals |
| TPR150 | 1 RGBHV
1 component video (Y, R-Y, B-Y)
1 S-video
1 composite video |
| Connectors | |
| TPT150 | 1 female RJ-45 jack |
| TPR150 | 1 female 15-pin HD (RGB)
3 female RCA (component video)
1 female 4-pin mini DIN (S-video)
1 female RCA (composite video) |
| Nominal level | 1 Vp-p for Y of component video and S-video, and for composite video
0.7 Vp-p for RGB
0.3 Vp-p for R-Y and B-Y of component video, and for C of S-video
± 0.1 Vp-p with 50' of TP cable between the TPT150 and TPR150 |
| Minimum/maximum levels | 0.24 V to 1.5 Vp-p |
| Impedance | 75 ohms |
| Return loss | -22 dB @ 5 MHz |
| DC offset | ±30 mV with input at 0 offset |
|
| Sync |
|---|
| Input type | RGBHV |
| Output type | RGBHV |
| Standards | NTSC 3.58, NTSC 4.43, PAL, SECAM |
| Input level | 2.3 V to 4.6 Vp-p, unterminated |
| Output level | 3.2 V to 4.6 Vp-p, unterminated |
| Input impedance | 1k ohms |
| Output impedance | 75 ohms |
| Max. input voltage | 4.6 Vp-p |
| Max. propagation delay | 760 ns |
| Max. rise/fall time | 35 ns |
| Polarity | Negative |
|
| Audio — TPT150 only |
|---|
| Gain | -30 dB to +9 dB, adjustable |
| Frequency response | 20 Hz to 20 kHz, ±5 dB |
| THD + Noise | 0.04% @ 1 kHz at nominal level |
| S/N | >-80 dB at maximum output |
| Crosstalk | <-80 dB @ 20 kHz, fully loaded |
| Stereo channel separation | >-70 dB @ 1 kHz |
|
| Audio input — TPT150 only |
|---|
| Number/signal type | 4 stereo, unbalanced |
| Connectors | 4 pairs of RCA connectors |
| Impedance | >7.8k ohms unbalanced, DC coupled |
| Nominal level | 2.22 dBu (1 Vrms) |
| Maximum level | +9 dBu, (unbalanced) at 1%THD+N |
| NOTE | 0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV ≈ 2 dBu |
|
|
| Audio output — TPT150 only |
|---|
| Number/signal type | 1 stereo, balanced/unbalanced |
| Connectors | (1) 3.5 mm captive screw connector, 5 pole |
| Impedance | 51 ohms unbalanced |
| Gain error | ±0.5 dB channel to channel |
| Maximum level (Hi-Z) | >+8 dBu, balanced or unbalanced at 1% THD+N |
| Maximum level (600 ohm) | >+4.2 dBm, balanced or unbalanced at 1% THD+N |
|
| Control/remote — transmitter (TPT150) |
|---|
| Serial control port | RS-232, 9-pin male D connector |
| Baud rate and protocol | 38400, 19200, 9600 (default), 4800, 2400, or 1200 baud (configurable); 8 data bits; 1 (default) or 2 stop bits; no parity (default), or even or odd parity |
| Serial control pin configurations | 2 = RX, 3 = TX, 5 = GND |
| Contact closure | (1) 3.5 mm captive screw connector, 8 pole for a CTP150CM control panel or locally constructed device |
| Contact closure pin configurations | 1 = input 1, 2 = input 2, 3 = input 3, 4 = input 4, 5 = volume up, 6 = volume down, 7= projector power, 8 = GND |
| Program control | Inline Control Software for Windows® – lCS100 |
|
| Control — projector (TPR only) |
|---|
| Projector control port | RS-232, 9-pin male D connector |
| Baud rate and protocol | 38400, 19200, 9600 (default), 4800, 2400, or 1200 baud (configurable); 8 data bits; 1 (default) or 2 stop bits; no parity (default), or even or odd parity |
|
| General |
|---|
| Power | 100 VAC to 240 VAC, 50 to 60 Hz, internal, autoswitchable
TPT150: 9 watts
TPR150: 20 watts |
| Ambient temperature/humidity | Storage: -40 to +158 °F (-40 to +70 °C) / 10% to 90%, noncondensing
Operating: +32 to +104 °F (0 to +40 °C) / 10% to 90%, noncondensing |
| Rack mount | |
| TPT150 | Yes, with included brackets, part #MTR102 |
| TPR150 | No, but projector pole mountable with included L brackets |
| Enclosure type | Metal |
| Enclosure dimensions | |
| TPT150 | 1.7" H x 17.0" W x 11.5" D (1U high, full rack wide)
4.3 cm H x 43.2 cm W x 29.2 cm D
(Depth excludes connectors. Width excludes rack ears. Height excludes rubber feet.) |
| TPR150 | 1.7" H x 11.75" W x 6.0" D (1U high)
4.3 cm H x 29.8 cm W x 15.2 cm D
(Depth excludes connectors. Width excludes rack ears. Height excludes rubber feet.) |
| Product weight | |
| TPT150 | 5.2 lbs (2.4 kg) |
| TPR150 | 2.2 lbs (1.0 kg) |
| Shipping weight | 13 lbs (6 kg) |
| DIM weight | |
| USA/Canada | 11 lbs (5 kg) |
| International | 12 lbs (6 kg) |
| Vibration | ISTA 1A in carton (International Safe Transit Association) |
| Listings | UL, CUL |
| Compliances | CE, FCC Class A |
| Product warranty | 3 years parts and labor |
| NOTE | All nominal levels are at ±10%. |
|
| NOTE | Specifications are subject to change without notice. |
|
| (7.51-020205-D6) |